Triangle Description: ordinary ordinary belt with a core with a core belt is mostly with core wire rope core, a small part of the use of cord with a core. Since both fiber with a core structure are twisted or establishment, in each belt operation between the fibers with a core shear leads to gradual elongation at break. Therefore, the use of wire rope core and ply belt with a common core production can only be applied in low-load transmission system. Special belt with a core with a core of special belt with steel core using brown silk polyester polymer overall solid core rod with a core structure. Because brown silk polyester steel solid core untwisted structure as a whole, good adhesion, resistance to flex, high strength, long run, not only greatly improve the life of rubber belts, but with the body balanced life, companies can do maintenance, periodic replacement. November 22, 2010, brown polyester steel wire reinforcing materials identified by the Committee of Experts: brown silk with polyester steel belt as a reinforcing material with conventional polyester cord, hard rope, aramid fiber rope structural skeleton Material belts compared to 5-10 times the service life, an international advanced level. With a core of special belts effectively solve the high-load heavy horsepower transmission belts frequent replacement of ordinary problems, much favored heavy industry around the world. C-belt applications Features Benefits a simple structure, manufacture, installation less precision, easy maintenance, belt suitable for two-axle center distance of two more occasions, smooth transmission, low noise, vibration absorption cushioning effect 3, When overloaded, the belt will slip on the pulley, can prevent damage to the weak parts, from the shortcomings of a security role, can not guarantee the accuracy of the ratio 2, outside dimensions greater transmission efficiency low edit this section when the reference length belt bent around the pulley rotates, its length and width remain unchanged level called the neutral layer. Under the provisions of the tension along the belt circumference neutral layer volume was called reference length Ld, also known as the nominal length. It is mainly used to calculate the geometry of the belt drive and belt marks, its length has been standardized. Also domestic belt length, as well as with the inner and outer perimeters represented. Edit this paragraph part of the normal belt rubber material generally consists of cloth covering, done layer (top gel), a strong layer (tensile layer) and a compression layer (primer) and other parts, the role of the different parts are as follows : 1. The cloth layer, the cloth covering is made into a plain plastic canvas beveled 45 ° (mainly cotton canvas and polyester canvas) composition, having excellent stretching and frictional resistance, can be connected to various parts of the integral, the protection other parts from wear and tear, erosion, and increase the role of stiff resistance V-belt. 2. stretching layer, the layer is done by high elasticity and excellent elongation properties of rubber composition, the V-belt to withstand tensile stresses during bending operation, and strong layer of cushion protection. 3. strong layer, strong skeleton V belt layer, the main types of polyester cord, steel brown silk polyester, aramid cord and dipped tire cord fabric, etc., is to bear the resulting V-belt during operation tensile stress, etc., is the belt drive during part of the main force. 4. cushion rubber, polyester or steel wire rope core Brown ribbon belt around a strong core layer, a layer with good adhesion strength with a core of plastic materials, namely rubber buffer, which play a fixed band the role of the core, and can absorb the dynamic shear stress belt deformation at high speeds frequently produced. 5. compression layer, compression layer is excellent resistance to bending fatigue properties of rubber composition to withstand bending belt and then run the compression stress generated thing, keep belt rigidity and elasticity, and plays an increasing belt section frictional contact with the pulley surface and improve the transmission efficiency of the role belt Caution: Due to the different roles of the different parts, so the rubber formulations used are different. Application Type Select type O, A, B type, C-type, D-type, E-type, F-type seven models, from O to F-type tape cross-sectional area increases. SPZ SPA SPB SPC These four models are narrow V-belt, XPA XPB XPZ a toothed belt. Select the tape speed model is based on the power of the tape passed to the decision, there are a lot of knowledge. Select models chosen triangle tape should adapt, otherwise triangle belt pulley groove will appear before the installation is not normal, if the two-axis center distance is adjustable structure should first center distance is shortened, then tape installed required to adjust the center distance; if two-axis center distance is not adjustable, you can set a belt to go into the round slot, and then turn to another pulley mounted on the triangle tape, using the same method to a set of Triangle tape are installed. Prohibit the installation tool to pry hard, hard pull on the belt, to prevent elongation triangle tape too tight or too loose phenomenon. When the tank is installed to prevent the string pulley, center on the two pulleys must be aligned, otherwise it will create a triangular tape unilateral work, badly worn, lower triangle belt life. Check correct installation check is: hand in the middle of each tape applied vertical pressure around two kilograms, sinking amount (20 - 30) mm is appropriate, inappropriate time to timely adjust. Mo old roots or mixed doubles when three or more triangular tape needs to be replaced, to use the specified type of triangle tape and ask each group triangle tape tightness agreement or allowed to reduce the number of old and new mixed use, otherwise the old belt force uneven, and even the old belt does not work, the impact of power transmission and shorten the life of the belt. Triangle C Part Number Index: C-belt C 1000 C 1016 C 1041 C 1067 C 1092 C 1100 C 1118 C 1143 C 1168 C 1194 C 1200 C 1219 C 1245 C 1270 C 1295 C 1300 C 1321 C 1346 C 1350 C 1372 C 1397 C 1400 C 1422 C 1448 C 1450 C 1473 C 1499 C 1500 C 1524 C 1549 C1 550 C 1575 C 1600 C 1626 C 1650 C 1651 C 1676 C 1700 C 1702 C 1727 C 1750 C 1753 C 1778 C 1800 C 1803 C 1829 C 1850 C 1854 C 1880 C 1900 C 1905 C 1930 C 1950 C 1956 C 1981 C 2000 C 2007 C 2032 C 2050 C 2057 C 2083 C 2100 C 2108 C 2134 C 2150 C 2159 C 2184 C 2200 C 2210 C 2235 C 2240 C 2261 C 2286 C 2300 C 2337 C 2350 C 2362 C 2388 C 2400 C 2413 C 2438 C 2450 C 2464 C 2489 C 2500 C 2515 C 2540 C 2550 C 2565 C 2580 C 2591 C 2600 C 2616 C 2620 C 2642 C 2650 C 2667 C 2692 C 2700 C 2718 C 2743 C 2750 C 2794 C 2800 C 2819 C 2820 C 2845 C 2850 C 2860 C 2870 C 2880 C 2896 C 2900 C 2920 C 2921 C 2946 C 2950 C 2960 C 2972 ??C 2997 C 3000 C 3020 C 3048 C 3099 C 3100 C 3120 C 3150 C 3175 C 3200 C 3251 C 3300 C 3302 C 3350 C 3353 C 3400 C 3404 C 3420 C 3429 C 3450 C 3454 C 3500 C 3505 C 3515 C 3520 C 3550 C 3556 C 3600 C 3607 C 3632 C 3650 C 3658 C 3700 C3708 C 3734 C3750 C 3759 C 3800 C3810 C 3850 C 3861 C 3900 C 3912 C 3937 C 3950 C 3962 C 3988 C 4000 C 4013 C 4039 C 4064 C 4089 C 4100 C 4115 C 4150 C 4166 C 4200 C4216 C 4242 C 4250 C 4267 C 4300 C 4318 C 4350 C 4369 C 4394 C 4400 C 4420 C 4445 C 4450 C 4496 C 4500 C 4521 C 4550 C 4572 C 4750 C4800 C 4826 C 4848 C 4850 C 4900 C 4950 C 4953 C 5000 C 5004 C5080 C 5100 C 5131 C5200 C 5231 C 5250 C 5283 C 5300 C 5334 C 5350 C 5400 C 5450 C 5500 C 5588 C 5600 C 5700 C 5800 C 5842 C 5850 C 5900 C 5950 C 5994 C 6000 C 6050 C 6096 C 6100 C 6150 C 6200 C 6250 C 6299 C 6300 C 6350 C 6400 C 6450 C 6500 C 6550 C 6700 C 6750 C 6800 C 6850 C 6858 C 7000 C 7050 C 7057 C 7100 C 7112 C 7200 C 7250 C 7300 C 7350 C 7400 C 7500 C 7550 C 7600 C 7620 C 7700 C 7800 C 7850 C 7900 C 8000 C 8100 C 8200 C 8250 C 8300 C 8400 C 8500 C 8600 C 8700 C 8800 C 8900 C 9000 C 8100 C 9144 C 9200 C 9300 C 9400 C 9500 C 9600 C 9700 C 9800 C 9900 C 10000 C 11000 C 11200 C 12000 C12500